![]() ![]() from the various property pages of plateĬharacteristics. The only thing I can think of is that youĪre bypassing the step where the software calculates the channel conversions Tested the function which generates channel conversions for the plates andĪll seemed to be working properly. With regards to the scaling problem with the data I am a bit perplexed. Problem was fixed regarding sampling times. Since the version you are running is dated 4/27/99 & the latest versionĪvailable is from 5/20/99 I suspect that you have software from before the >below, and those not listed on page 1 of the manual (under board set up) are The full set of parameters displayed are shown However, there are a few other parameters listed >anything else, as the rest of the settings appeared to match those of the >selected CIO-DAS16/330 from the list of board type options. >listed (board # 0 to board # ? (I can't remember how many boards were > When I opened Instacal, then looked under 'install', all the boards >since I have received no further details, I assume that the manual >that you would e-mail me this information if this were the case. >have had to alter some of the settings from those listed in the manual and >board settings, you said to access the Instacal program and to just follow ![]() >solve the problem of accessing the Ariel analogue program). >analogue board software (a procedure you recommended that we try in order to >might need re-setting as they could have changed when we re-installed the Your suggestion was that the analogue board switch settings >time we spoke I informed you that the EMG software was not reading the >system to work, but we are still having problems. Today, we spent the morning trying to get the EMG >finally free to spend the necessary time required to become familiar with > Now that Fall quarter is over and the final grades are in, Naz and I are In a message dated 12/17/98 9:50:50 PM Eastern Standard writes: I will get it as soon as I and check it out and send it off to you if the problem is solved.JeremyĬlearly a number of the settings are wrong. They have a fix in the form of an updated version of CBW32.DLL. It should work if all of the sharing boards are so disabled.I contacted Computerboards about this & they confirmed that the board indeed will not work if there is interrupt sharing. If you find another board using this interrupt go to the properties for that board and check the 'Disable' checkbox. If there are other boards listed as using this same interrupt the A/D does not work. A listing of the interrupt#'s and the boards which use them will appear. Go to Device Manager, highlight 'Computer' and click on the properties button. ![]() The board will not work properly if it is sharing an interrupt# with another board. I have installed the PCI analog board in my system & I think I understand the nature of the problems which have been encountered trying to get the PCI version of the boards working.It basically boils down to this. The phone as I have almost no e-mail regarding it. It appears that the bulk of our contact regarding this was over Or, should you remember, just pass this infoĪlong to me. So I need you to go thru the process of installing aīoard on a system with the new CB Install and give me a detailed description I cannot remember the details and the people at CB drew blanks when I vaguelyĭescribed the problem. We solved the problem by going back to an older version of theeir Install. Is correct, there was a problem when we used the new version of the CB setup.ĬANA could not execute because the system could not find something or another. Weeks ago when you tried to install a system with a board. You can also see your Reminders list, and add new reminders as well as view and edit existing ones.I have contacted Computerboards regarding the difficulty we encountered a few From there you can view your calendar events, make changes, invite friends or even add new events. InstaCal is quick and convenient, and can be opened at any time with a configurable keyboard shortcut. InstaCal is an affordable, yet powerful calendar app that puts all your events right at your fingertips, always available in your Mac's menu bar. InstaCal is the missing menu bar calendar macOS deserves. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |